User:Mantaskosmo

From DigitalCraft_Wiki
Revision as of 20:18, 28 June 2015 by Mantaskosmo (talk | contribs)
Jump to navigation Jump to search

Rhythmical Staircase "Rhythmical staircase" is a project created in order to increase visitors spatial averseness. “Rhythmical Staircase” installation translate the rhythmical movement of walking through the stairs into proverbially equivalent “one, two, one, …”.

Concept The meeting between body and world is natural as well as culturally and conventionally produced. The rhythmic experience is likely to be found in aesthetic of visual and audible movement. Rhythm is multisensory and appeals to our tactile, visual, and sonic senses. The stair is an architectural part that appeals to all the senses. The stair meets us as a passage and a sequence experienced over time. It’s ‘here and now’ experience which coordinates with memories of past experience and what is present. The movement in a staircase leads up and down, and physically it is the part of the building that interacts with our bodies. Visually, the movement is already inscribed as a repetition in construction, which audibly can be described as the rhythm of the steps echoing, the beating of the heart and the rhythm of breathing. It is natural for us so we don’t think about it. In order to increase visitors spatial averseness “Rhythmical Staircase” installation translate the rhythmical movement of walking through the stairs into proverbially equivalent “one, two, one, ...”

Progress Roughly, the installation is made of two circuits - one is a IR (infrared) LED light circuit, and photodiodes circuit. LED circuit is connected to 9V power source and photodiodes circuit is connected to Arduino MEGA which is later programmed in processing. Photodiodes are installed on a side of a staircase and directed to a LED light in the other side of a stair. Once the light is covered, photodiode value drops to minimum and that triggers processing to play the sound.

To make 13 interactive stairs you will need: 13 IR LED lights ( I used Kingbright T-1 3/4 (5mm)) 13 Photodiodes ( I used Taos TSL260R ) Arduino MEGA ( if you use up to 6 staircase you can also use Arduino UNO which has 6 analog inputs instead of 13. (It is possible to use Arduino UNO for more than 6 staircase but the instructions than different )). Wires ( depending on your circuits, the size of the staircase, also how far is the ‘station' (computer and power source)) I used around 200 meters of wires and my ‘station’ was about 2 meter from the circuits. 9V power adapter ( for LED circuit) 2x 1ohms resistor ( for LED circuit) 390ohms resistor ( for LED circuit) Arduino app Processing app

IR LED lights circuit For my circuit I used this array. If you will use different LED or power supply, you can calculate your array here: http://led.linear1.org/led.wiz


Photodiodes Circuit Photodiode have 3 pins. Ground (GND) and Power supply pin (VDD) circuits should be connected to Arduino GND and 5V inputs. 3rd pin is an output which separately have to be connected to Arduino analog input.


Photodiodes connected in GND and VDD circuit.

I am highly recommending to use different colours wires for GND and VDD circuits.


The whole circuit will look like this at the end.


Photodiodes connected to Arduino. Big amount of wires requires good infrastructure that’s why I recommend to number wires or use different colours wires.


Photodiodes are sensitive from all the sides. To make it directed to LED light source you have to make ‘a tunnel’ which would isolate sensor from surrounded light and would be directed only to a LED lights in the other side of a stair.


Arduino app First of all you will probably want to check photodiodes incoming value. To check it you can use this code:


The value from photodiodes should be sent to Processing app. To connect, use this code:


Processing app Processing code connected with audio files and Arduino app:

Processing code is linked with audio files which had to be uploaded on the same directory as code file.