|
|
| Line 2: |
Line 2: |
| | | | |
| | [[Digital Craft 2nd Year]] | | [[Digital Craft 2nd Year]] |
| − |
| |
| − |
| |
| − | [[File:hyunji.jpg|300px]]
| |
| − |
| |
| − | angiethebard@gmail.com<br>
| |
| − | 0915620
| |
| − |
| |
| − |
| |
| − | == First Class ==
| |
| − | [[File:gr5.jpg|300px]] [[File:gr5.1.jpg|200px]]
| |
| − |
| |
| − | I grouped up with Mickey, Axel and Ayo. Denis gave us a lecture about basic electricity. We did a small exercise to show what we learned from the class. We did a small play to show how plus and minus electrons work when they are close and far from each other.
| |
| − |
| |
| − |
| |
| − | == Second Class ==
| |
| − | We experimented with small circuit boards and batteries.<br>
| |
| − | [[File:digi3.jpg|200px]]
| |
| − |
| |
| − | Battery: -8.78V (We switched around the + and the -, so the reading is in -. But we saw and changed it so it was right, but forgot to picture it.)<br>
| |
| − | Resistance: 470 ohms<br>
| |
| − | Current: 13.8 mA<br>
| |
| − |
| |
| − | <br>
| |
| − | '''Measuring Voltage and Current'''<br>
| |
| − | [[File:digi4.jpg|200px|]] [[File:digi9.jpg|200px]] [[File:digi10.jpg|200px]]
| |
| − | 9V battery and diode
| |
| − |
| |
| − |
| |
| − | Here we measured the resister.
| |
| − |
| |
| − | [[File:Resister1.JPG|200px]] [[File:Resister2.JPG|200px]] [[File:Resister3.JPG|200px]] [[File:5.jpg|200px]]
| |
| − |
| |
| − | Volt 1st resistor 9.83 Volt / 2nd 0.32 Volt / 3th 0.18 Volt/ 1th + 2nd together 10.15 Volt / 2nd + 3th together 0,5 Volt / 1th +2nd +3th together 10.83
| |
| − |
| |
| − | I = V/R
| |
| − | 9,11: 9,83 = 0,93
| |
| − | 9,11 : 10.83 = 0,84
| |
| − |
| |
| − | We measured the different resisters so we knew the value.
| |
| − |
| |
| − | == Third Class ==
| |
| − | [[File:noise_01.jpg|300px]] [[File:noise_02.jpg|300px]]
| |
| − |
| |
| − | To be honest, I missed half of the class because of the unmatched planning on mywdka and wike page. I tried to follow what was going on during the class and Denis explained me what I could do.
| |
| − | And then I realised I actually did the similar thing at an open course last year which was about making a circuit that makes noise when you touch. I could also made a noise with water.
| |
| − |
| |
| − |
| |
| − | == Individual Project ==
| |
| − | '''Previous Work'''<br>
| |
| − | [[File:carto01.jpg|300px]] [[File:carto02.jpg|300px]]
| |
| − |
| |
| − | I made an weaving loom with LED at quarter 6 at fine art department and decided to develop the work. The concept was about weaving my own tapestry as a traveller. Since I have mainly worked with textile so far and I wanted to make my own textile. I got the idea of weaving a tapestry from a travel to Morocco. I visited Berber people's village and could see many tapestry works of them. They are also nomadic tribe. I have travelled a lot and now I am staying in the Netherlands. Therefore I wanted to describe my identity by weaving a tapestry. The light from the fibres signifies the star constellation, which guides you find the direction when you are lost on trip.
| |
| − |
| |
| − | I decided to continue this work for this practice. This time, I wanted to make a wearable object like smart textile. I already had the material "optical fibre". I decided to make a cape which also signifies traveller, and to weave optical fibre through the cape. At the beginning I just wanted to use some LEDs and Arduino to programme some changes in the light as before. But when I talked to the teachers they suggested me to use light sensor "LDR", and I thought it would be awesome. So I decided to make a fibre-woven, lighted cape that interacts with lightness of surroundings.
| |
| − |
| |
| − |
| |
| − | ----
| |
| − |
| |
| − | '''Circuit and Material'''<br>
| |
| − | [[File:circuitdrawingtom.jpg|300px]]<br>
| |
| − | So I asked Thomas for help to make a circuit. I could get the light source from the package with optical fibre. I also measured the voltage and current of each R, G, B lines and white wire for + but forgot to take pictures..
| |
| − | From the result of measurement, I could know which transistor and resistor I need for this circuit.<br>
| |
| − | 3 x '''BD139 transistor''' for each R, G, B lines<br>
| |
| − | 3 x '''360 ohm resistor''' for each R, G, B lines<br>
| |
| − | 1 x '''10K ohm resistor''' for Arduino<br>
| |
| − | 1 x '''LDR''' (Light sensor)
| |
| − |
| |
| − | ----
| |
| − |
| |
| − | First I tried with breadboard and then it worked properly. Then I soldered the actual circuit.<br>
| |
| − | [[File:circuitfiber01.jpg|300px]]
| |
| − |
| |
| − | However, when I took this to the last class and tried out if it works, there was a problem with the LDR-resistor part. When I tried to plug the voltage pin on Arduino it got really hot. Denis explained to me it was because I connected the voltage and ground so it was making a very short circuit. So I changed the connection between LDR and resistor. Then it started to work, but the value of LDR was not changing that significantly. It was in between 974-1024. So I asked Thomas and he said there is another error again.<br>
| |
| − | [[File:correctionldr.jpg|300px]]
| |
| − |
| |
| − | However, even after I fixed the circuit, LDR was working the same and for some reason, Red light was not working. I think I broke the transistor while I was soldering. Same thing happened to me before when I was soldering too long and too hot. So I had to give up some of my original plan. My original plan was to make the light brighter in the dark and after I realised the red light was not working, I wanted to programme like when it's dark, there is more Blue value and when it gets lighter it has more green value. But then LDR was not working. So I dropped the idea of programming complicated. I just put the blue and green light together all the time. Then finally it worked!<br>
| |
| − | [[File:circuitfiber02.jpg|300px]]
| |
| − |
| |
| − |
| |
| − | There were many small mistakes during the process but to summarise what I failed are:<br>
| |
| − | '''Use of LDR'''<br>
| |
| − | '''Complicated programming'''
| |
| − |
| |
| − | I kind of pushed myself to try out more complex circuit than I did before. But unfortunately not everything worked out as planned. But still, I learned new things such as how to prevent making a short circuit, how to measure voltage and current to know the right resistor, and I also vaguely remember DC and AC therefore I need a transistor. I still want to try to fix the circuit to accomplish my original goal and revise all new things I learned from the process.
| |
| − |
| |
| − |
| |
| − | ----
| |
| − | I still need to put the picture of my end result. It's trippy.
| |
