User:Willemhampson

Hello

Name: Willem Hampson

Email: willemhampson@hotmail.co.uk

Digital Craft

The moment I knew What I wanted to do

I think it has always been an ambition of mine to work in the arts but I do not remember a specific moment, my interest in making illustration my profession is a result of a culmination of inspirations, for example books such as the 'Tintin' series that entertained me as a child and continue to inspire me now.

What do you make?

I'm still trying to figure out a consistent way of working for myself. I start the majority of my work by drawing in pen or pencil but where it goes after that can vary.

What is your topic of interest?

One of my current topic of interest is publishing and how various forms of printing could advance my work, I haven't done very much of either however I find having your own work turned into some kind of physical edition highly rewarding.

What is your medium?

My answer to this is similar to the question of "what do you make?" in that I haven't settled on one specific medium, I like to work in pencil, pen, paint and ink. Softwares are becoming more important to my work, mainly Photoshop, Indesign and Illustrator (depending on the brief or project).

Circuit Board

We connected a touch sensitive circuit board to LED lights and a speaker in small groups.

Video link here -> [1]

Personal Project

I enjoy accidental and unintentional textures/marks that are made in my work. I would like to make some kind of machine that could make such marks for me. Something that reacts fairly unpredictably to the actions of the user.

Inspiration

Gerhard Richter is an artist who paints with materials that do not dry immediately, he will then takes a large rubber implement and drags it across the work, pulling all the wet paint with it. Although this effect is intentional, there's no way he can know exactly how the paint will react.

Ralph Steadman is an illustrator and cartoonist. Although his drawings are not abstract, he makes marks by splashing and blowing ink across the page, before working in to it.

Project experimentation and development

I decided a vibrating motor would be essential to my machine and started by getting hold of one of those. I thought it would be interesting to experiment with using the touch sensor to activate it. I simply replaced the speaker (shown in the 'circuit board' video link earlier) with the vibrating motor. This achieved a small amount of success and although the motor responded, it would not have been enough to result in the movement of other components. Instead I tried to make a circuit using a switch instead of a touch sensor. This had a much better result so I decided to test it and attached a pen to the vibrating motor.

I began experimenting by attaching a variety of pens to to the motor and seeing what kind of marks I could get on paper. Watch video experimentation link -> [2]

As shown in the video, I tried to attach 4 mark making items at once to a ruler to imitate my final machine. Perhaps there was too much weight in this as the motor was not powerful enough to create interesting movement.

To try and resolve this I assumed an extra motor might give the extra power that I needed. Unfortunately this did not work and only one of the motors vibrated. I may look into the appropriate circuit to make both of them work.

Despite that, the rest of the experiment was fairly interesting. Here is the result.

I really liked the small dashed lines made the pen with a thin nib, with this in mind I made a quick sketch of a friend of mine with the motor switched on.

Further development

With the basic model made, I started to work on improving it. At the end of my last video I had attached the motor to a ruler and four mark making items. I found that the brushes did not react much to the motor due to the soft tip touching the paper. These I would simply replace with other pens or try to figure out a way of applying more power in the vibration. I also assumed that the weight in the ruler would have held down the four points of contact on the paper, and reduced the affect of the motor, for this reason I selected a lightweight foam board to test out my product.

Stage 1

I cut the foam board piece after measuring and drawing it out. On the four corners I put extensions with grooves to hold the pens. These were also held by elastic bands above and below the foam board. This was impractical however, and the pens kept slipping out. Instead I decided to go for two pieces with grooves for the pens, and only one elastic band per pen.

Stage 2

For increased strength and stability I cut away the corners of the square as slots for the pens. This stage worked to some extent however I felt that it was almost too stable to react much to the vibrating motor.

Stage 3

Due to four pens attached at once having little movement, I decided to go for 3 instead (hence the triangular shape). I needed both pieces to be identical so that the pens would be held in place properly so I laser cut them.

watch video [3]

Mimicking Machines

Assignment 1

I Draw. You Draw. It Draws

The first assignment involved drawing our favourite machine with instructions for someone else to imitate this drawing. I used a grid format with an x and a y axis as I thought the instructions for this would translate easily and someone would be able to follow it. The machine I drew was a guitar amplifier.

We also took our own vector drawings and had them digitally drawn on a machine usually used for cutting shapes with a blade. The blade was simply replaced with a ballpoint pen.

Assignment 2

3D letters

I started by sketching a letters in pencil, when I was settled on a design I scanned it and used Adobe Illustrator to trace over it. This vector file was then taken into sketchup where I made it a 3D digital file.