Screenprint cleaning - Revision history

Baschz: /* Wash off ink after printing */

2023-04-12T06:50:30Z

Wash off ink after printing

← Older revision		Revision as of 06:50, 12 April 2023
Line 3:		Line 3:

	== Wash off ink after printing ==		== Wash off ink after printing ==
	Use the shower head to rinse the inside of the screen to wash off most of the ink. Then use ~~the~~ sponge to scrub all the left over ink off the screen on both sides and rinse again with water.		Use the shower head to rinse the inside of the screen to wash off most of the ink. Then use a sponge and soap to firmly scrub all the left over ink off the screen on both sides and from the inside of the frame, then rinse again with water.

	== Clean emulsion off the screen ==		== Clean emulsion off the screen ==
	Wash the ink off (as above) and apply emulsion stripper with a brush to both sides of the screen. Make circles with the brush and work it in very thoroughly. Switch on the compressor and use the power washer to blast the emulsion out off the screen. Keep it at a close distance to the screen (~~1cm0~~ to get everything off and to not get as wet yourself. Apply ~~soft green~~ soap to the screen and wash it in on booth sides with the sponge. Then use the power washer with the compressor on at close distance again to clean out any left over inks.		Wash the ink off (as above) and apply emulsion stripper with a brush to both sides of the screen. Make circles with the brush and work it in very thoroughly. Switch on the compressor and use the power washer to blast the emulsion out off the screen. Keep the head at a close distance to the screen (1cm) to get everything off and not get wet yourself. Apply soap to the screen and wash it in on booth sides with the sponge. Then use the power washer with the compressor on at close distance again to clean out any left over inks.

	== Deep cleaning (anti ghost) ''Station Staff Only'' ==		== Deep cleaning (anti ghost) ''Station Staff Only'' ==

Wilco at 19:56, 25 January 2023

2023-01-25T19:56:59Z

← Older revision		Revision as of 19:56, 25 January 2023
Line 1:		Line 1:
	== After exposing: ==		== After exposing ==
	Use the ~~hose~~ to make ~~booth side’s off~~ the screen wet and rinse from the inside of the screen. Do this ~~till~~ you washed away all the non exposed emulsion.		Use the shower head to make both sides of the screen wet and rinse from the inside of the screen. Do this until you washed away all of the non exposed emulsion, and you can see through it.

	== Wash off ink after printing ==		== Wash off ink after printing ==
	~~With~~ the ~~hose~~ rinse the inside ~~off~~ the screen to wash off the ink, use the ~~spons~~ to ~~clean~~ the screen ~~from the ink~~ on ~~booth~~ sides and ~~rise~~ again with water.		Use the shower head to rinse the inside of the screen to wash off most of the ink. Then use the sponge to scrub all the left over ink off the screen on both sides and rinse again with water.

	== Clean screen ~~from emulsion~~ ==		== Clean emulsion off the screen ==
	Wash ~~off~~ the ink (~~see~~ above) apply emulsion ~~remover~~ with a brush to both sides ~~off~~ the screen. Make circles with the brush and ~~wash~~ it in very ~~thorough~~. Switch on the compressor and ~~Use~~ the ~~water gun~~ to blast the emulsion out of the screen.		Wash the ink off (as above) and apply emulsion stripper with a brush to both sides of the screen. Make circles with the brush and work it in very thoroughly. Switch on the compressor and use the power washer to blast the emulsion out off the screen. Keep it at a close distance to the screen (1cm0 to get everything off and to not get as wet yourself. Apply soft green soap to the screen and wash it in on booth sides with the sponge. Then use the power washer with the compressor on at close distance again to clean out any left over inks.
	~~With~~ a ~~spons apply~~ soft green soap to the screen wash it in ~~form~~ booth sides
	~~And~~ use the ~~water gum~~ with the compressor on to clean out ~~the~~ left over inks.

	== Deep cleaning (anti ghost) ==		== Deep cleaning (anti ghost) ''Station Staff Only'' ==
	~~This is for the station staff to do.~~ '''Wear protective clothes, gloves and ~~eyewear~~.'''		'''Wear protective clothes, gloves and glasses.'''
	Apply anti-ghost gel with a ~~scoopcoater~~ to a dry screen on one side of the screen let the anti-ghost gel dry for 15 minutes (not longer) avoid that the screens come in contact with water let them dry outside the washing booth.		Apply anti-ghost gel with a scoop coater to a dry screen on one side of the screen let the anti-ghost gel dry for 15 minutes (not longer) avoid that the screens come in contact with water (let them dry outside the washing booth).

	Use the ~~water gum~~ with the compressor switched on ~~start~~ at the bottom of the screen and work to the top to blast out everything ~~that’s left in the screen~~. Turn the screen around ~~And blast~~ out ~~wat is~~ left ~~over~~ in the screen. ~~Rise~~ the screen with the ~~hose the~~ wash off ~~the lest~~ over anti-ghost ~~gell~~ before ~~the~~ place the screen back in the rack.		Use the power washer with the compressor switched on. Start at the bottom of the screen and work to the top and blast out everything. Turn the screen around and take out what's left in the screen. Rinse the screen with the shower head to wash off any left over anti-ghost gel before you place the screen back in the rack.

Wilco: Created page with "== After exposing: == Use the hose to make booth side’s off the screen wet and rinse from the inside of the screen. Do this till you washed away all the non exposed emulsion. == Wash off ink after printing == With the hose rinse the inside off the screen to wash off the ink, use the spons to clean the screen from the ink on booth sides and rise again with water. == Clean screen from emulsion == Wash off the ink (see above) apply emulsion remover with a brush to b..."

2022-08-31T17:49:22Z

Created page with "== After exposing: == Use the hose to make booth side’s off the screen wet and rinse from the inside of the screen. Do this till you washed away all the non exposed emulsion. == Wash off ink after printing == With the hose rinse the inside off the screen to wash off the ink, use the spons to clean the screen from the ink on booth sides and rise again with water. == Clean screen from emulsion == Wash off the ink (see above) apply emulsion remover with a brush to b..."

New page

== After exposing: ==
Use the hose to make booth side’s off the screen wet and rinse from the inside of the screen. Do this till you washed away all the non exposed emulsion.

== Wash off ink after printing ==
With the hose rinse the inside off the screen to wash off the ink, use the spons to clean the screen from the ink on booth sides and rise again with water.

== Clean screen from emulsion ==
Wash off the ink (see above) apply emulsion remover with a brush to both sides off the screen. Make circles with the brush and wash it in very thorough. Switch on the compressor and Use the water gun to blast the emulsion out of the screen.
With a spons apply soft green soap to the screen wash it in form booth sides
And use the water gum with the compressor on to clean out the left over inks.

== Deep cleaning (anti ghost) ==
This is for the station staff to do. '''Wear protective clothes, gloves and eyewear.'''
Apply anti-ghost gel with a scoopcoater to a dry screen on one side of the screen let the anti-ghost gel dry for 15 minutes (not longer) avoid that the screens come in contact with water let them dry outside the washing booth.

Use the water gum with the compressor switched on start at the bottom of the screen and work to the top to blast out everything that’s left in the screen. Turn the screen around And blast out wat is left over in the screen. Rise the screen with the hose the wash off the lest over anti-ghost gell before the place the screen back in the rack.