Difference between revisions of "Screenprint cleaning"

From Publication Station
(Created page with "== After exposing: == Use the hose to make booth side’s off the screen wet and rinse from the inside of the screen. Do this till you washed away all the non exposed emulsion. == Wash off ink after printing == With the hose rinse the inside off the screen to wash off the ink, use the spons to clean the screen from the ink on booth sides and rise again with water. == Clean screen from emulsion == Wash off the ink (see above) apply emulsion remover with a brush to b...")
 
Tag: visualeditor
 
(One intermediate revision by one other user not shown)
Line 1: Line 1:
== After exposing: ==
== After exposing ==
Use the hose to make booth side’s off the screen wet and rinse from the inside of the screen. Do this till you washed away all the non exposed emulsion.  
Use the shower head to make both sides of the screen wet and rinse from the inside of the screen. Do this until you washed away all of the non exposed emulsion, and you can see through it.  


== Wash off ink after printing ==
== Wash off ink after printing ==
With the hose rinse the inside off the screen to wash off the ink, use the spons to clean the screen from the ink on booth sides and rise again with water.  
Use the shower head to rinse the inside of the screen to wash off most of the ink. Then use a sponge and soap to firmly scrub all the left over ink off the screen on both sides and from the inside of the frame, then rinse again with water.


== Clean screen from emulsion ==
== Clean emulsion off the screen ==
Wash off the ink (see above) apply emulsion remover with a brush to both sides off the screen. Make circles with the brush and wash it in very thorough. Switch on the compressor and Use the water gun to blast the emulsion out of the screen.  
Wash the ink off (as above) and apply emulsion stripper with a brush to both sides of the screen. Make circles with the brush and work it in very thoroughly. Switch on the compressor and use the power washer to blast the emulsion out off the screen. Keep the head at a close distance to the screen (1cm) to get everything off and not get wet yourself. Apply soap to the screen and wash it in on booth sides with the sponge. Then use the power washer with the compressor on at close distance again to clean out any left over inks.
With a spons apply soft green soap to the screen wash it in form booth sides  
And use the water gum with the compressor on to clean out the left over inks.  


== Deep cleaning (anti ghost) ==
== Deep cleaning (anti ghost) *''Station Staff Only''* ==  
This is for the station staff to do. '''Wear protective clothes, gloves and eyewear.'''  
'''Wear protective clothes, gloves and glasses.'''  
Apply anti-ghost gel  with a scoopcoater to a dry screen on one side of the screen let the anti-ghost gel dry for 15 minutes (not longer) avoid that the screens come in contact with water let them dry outside the washing booth.  
Apply anti-ghost gel  with a scoop coater to a dry screen on one side of the screen let the anti-ghost gel dry for 15 minutes (not longer) avoid that the screens come in contact with water (let them dry outside the washing booth).  


Use the water gum with the compressor switched on start at the bottom of the screen and work to the top to blast out everything that’s left in the screen. Turn the screen around And blast out wat is left over in the screen. Rise the screen with the hose the wash off the lest over anti-ghost gell before the place the screen back in the rack.
Use the power washer with the compressor switched on. Start at the bottom of the screen and work to the top and blast out everything. Turn the screen around and take out what's left in the screen. Rinse the screen with the shower head to wash off any left over anti-ghost gel before you place the screen back in the rack.

Latest revision as of 06:50, 12 April 2023

After exposing

Use the shower head to make both sides of the screen wet and rinse from the inside of the screen. Do this until you washed away all of the non exposed emulsion, and you can see through it.

Wash off ink after printing

Use the shower head to rinse the inside of the screen to wash off most of the ink. Then use a sponge and soap to firmly scrub all the left over ink off the screen on both sides and from the inside of the frame, then rinse again with water.

Clean emulsion off the screen

Wash the ink off (as above) and apply emulsion stripper with a brush to both sides of the screen. Make circles with the brush and work it in very thoroughly. Switch on the compressor and use the power washer to blast the emulsion out off the screen. Keep the head at a close distance to the screen (1cm) to get everything off and not get wet yourself. Apply soap to the screen and wash it in on booth sides with the sponge. Then use the power washer with the compressor on at close distance again to clean out any left over inks.

Deep cleaning (anti ghost) *Station Staff Only*

Wear protective clothes, gloves and glasses. Apply anti-ghost gel with a scoop coater to a dry screen on one side of the screen let the anti-ghost gel dry for 15 minutes (not longer) avoid that the screens come in contact with water (let them dry outside the washing booth).

Use the power washer with the compressor switched on. Start at the bottom of the screen and work to the top and blast out everything. Turn the screen around and take out what's left in the screen. Rinse the screen with the shower head to wash off any left over anti-ghost gel before you place the screen back in the rack.